Jamie
- Access Motors
|
"Mechanics
are always being plagued with the dreaded nut or bolt
that fell... somewhere. Murphy's law ensures that
it never quite makes it all the way to the ground.
It has rapidly become a favorite among our technicians
for exploring unreachable recesses in and around the
cars in our shop. I'm sure we'll continue to find
more uses for this little life saver as time goes
by, but so far, I'd say that it has earned its keep
just fine."
B.
D.
Service Manager
Toyota Dealership
Norman, OK
|
"We use the ProVision
as a teaching tool for turbine engine technology classes. This
tool enables students/mechanics to do on the spot internal engine
inspection quickly and easily. We don't need any other
tool. ProVision 100 finds problems right on the spot.
And it's affordable... not nearly as expensive as boroscopes.
ProVision is neat, compact,
lightweight, fits handily in a toolbox. I like the fact
that it uses standard AA battery that I can buy anywhere."
H.
B.
Aviation Maintenance Technician Instructor
"As
an electrician, I was searching for a tool that would allow
me to see what the existing conditions were inside the stud
space of walls before drilling into unknown areas or creating
the mess and added cost of removing drywall.
The ProVision 100
is a life saver! It has easily paid for itself many times
over in the short amount of time that we have been using them
on our service trucks."
J. G.
Southwest Valley Electric
"We
have found it very useful for viewing shock absorber
assemblies. Specifically to inspect wear patterns in
the cylinder walls after life cycle testing has been
completed. This is a time saver as we had needed to
cut the bodies apart to get a good look at the patterns
before. The small scope is excellent for viewing the
actual assembly movement of our adjustable damping circuits
through their range of adjustment."
Scott
Progressive Suspension |
|
"I
work for a testing and inspection firm. We purchased a ProVision
300 for inspecting small, hard to get to spaces.
This tool is definitely a time saver. Using the ProVision
allows us to inspect things quicker and easier. My only regret
is that we didn’t get one sooner."
J. C.
The Twining Laboratories, Inc.
"A
lifesaver INDEED! Thanks ProVision
for this flexible optical device. A motor vehicle with high
emissions came in today and after a few checks which proved
OK, I proceeded to inspect the catalytic convertor, and without
dropping the entire exhaust system I was capable of viewing
both sides of the convertor which proved defective. What an
aid to my diagnostic capabilities, what a time saver!"
R. E. D.
Automotive Technician
"The
ProVision is
a needed tool for the law enforcement community. It's a
valuable and useful tool for crime scene investigation and
all aspects of law enforcement. It's good for looking into
backseats of autos or in inaccessible areas like a gas tank.
Instead of tearing something apart you can use ProVision
for easy and quick checks. ProVision
is very useful, fast and easy. And great
for contraband checks."
L.
P.
Lone Star Forensics
Hurst, TX
"I
am able to determine friction plate thickness and other clutch
related problems without spending a lot of time removing transmissions.
The ProVision is
great, well worth what we paid."
T.
S. Purcell, OK
"We
bought the ProVision
to inspect the internal areas of pump impellers. The
first time we used it we found cracks inside the impeller
that would have gone undetected, and could have caused
a catastrophic failure in the pump. Thanks for
a great tool."
C.
A.
Westvaco
Chandler, AZ |
|
"We
were really skeptical about investing in another boroscope.
We had purchased 2 other brands before yours and they were
basically worthless. Today we had a ‘97 Grand AM come
in with a coolant leak. After pressure testing we were convinced
of a bad cyl head/gasket. Well, after using your scope to
see the engine better, we determined that the leak was indeed
from the cylinder head. We would not have found this problem
until after the head was removed had we not used your scope!"
G.
I.
DG’s Auto
Orlando, FL
"I
work at the Kennedy Space Center’s Visitors complex in
Florida. My job is at fleet maintenance where we are required
to keep our 60 coaches in tip-top shape. On some of our older
buses we needed to find out the condition of the inner frame
behind the outer skin. Your ProVision
flexible fiberoptic scope was just the right tool for
the job. We were able to inspect the coaches without
removing the outer panels thus saving us a lot of work and
expense. Thanks much for such a fine product."
J.
E.
Johnson Controls
Kennedy Space Center
Titusville, FL
"I install satellite TV systems and smart home components.
I always had problems retrieving a wire that I've threaded through
a hole into a wall cavity. Many times I've been frustrated and
had to cut at least a 4" hole. Now, with the ProVision,
all I cut is a 1" hole where I'm going to place the telephone,
cable or network jack. Then I use the ProVision,
to which I tape a coat hanger wire with a hook on the end. This
way, I can find the cable and hook onto it at the same time,
and pull it out of the hole. It's great!"
I.
L.
"Being
very leery of new tools like this, I bought it anyway. After
buying the tool it was less than a week that I actually used
it. Being a diesel mechanic, the job I was doing would have
taken me about 7 hours to determine the problem. With ProVision
it only took me about 30 minutes. This thing is worth
every penny I paid for it."
R.B. Clinton, IA
"I
have been waiting for years for someone to make a tool like
this. I have used it several times already with great results.
What a time saver."
S.B. Temecula, CA
"The
ProVision fiberoptic
scope has saved me five hours labor on trouble-shooting
engine noise. This is one of the best tools I have purchased."
J.Z.
"A
couple of months ago our local tool distributor introduced
me to ProVision
and showed me how it worked and the benefits of tear down
time I could save with its use. I have looked into several
types of scopes and could not understand how your scope was
much easier to operate and inexpensive all in one, I was skeptical!
I wanted to put it to the test first, so I copied the phrase
"you sold me" in the smallest type possible and
placed it at the bottom of an empty soda can. I asked the
tool dealer if he could read the print. When he read the phrase
back to me I was sold! I am glad I purchased the ProVision
that same day and enjoy using it every chance I get. Thanks
for a product that every technician should have in their
tool box."
J.C. Kingman, AZ
"I
recently purchased my ProVision
and it has already paid for itself in time saved.
I was working on an Isuzu and it had problems in a
cylinder with no compression. One look with the ProVision
and I knew the motor had to come out because of burnt pistons.
It also saved the day on a Dodge Caravan that we thought
the heads were leaking under the intake manifold. We took
a quick look with the ProVision
and it showed us that it was the water pump leaking under
the intake. Thanks for a great tool. I did not know how much
I needed one until I got mine!"
A.K. Texarkana, AR
"We
never imagined how useful the ProVision
would be when we bought it. Now we have one on every
truck because it allows us to inspect those old Lennox
and Carrier units without tearing them apart. We are
selling more new furnaces than ever before."
B.B. Wichita, KS
"This
thing has paid for itself over and over again in the time
we have saved at a number of jobs. I never thought of using
a tool like this, now I can’t imagine doing my
job without it."
T.C. Chicago, IL |
